ISO 4406 Explained – Hydraulic Oil Cleanliness

Your hydraulic oil may look clean, but how clean is it really? Many of the particles that damage pumps, valves and bearings cannot be seen with the naked eye. ISO 4406 allows engineers to quantify this contamination and monitor improvements.

1. What is ISO 4406?

ISO 4406 is an international coding system for solid particle contamination in hydraulic and lubricating oils. A result such as ISO 22/20/17 gives cumulative particle concentration bands at ≥4 µm(c), ≥6 µm(c) and ≥14 µm(c), respectively. One micron is one thousandth of a millimetre. Generally, lower numbers mean fewer particles.

Particle sizes compared with human hair and representative hydraulic component clearances
Particle-size comparison: many damaging particles are far too small to see unaided.

2. Understanding ISO 22/20/17

Particle size ISO code Particles per millilitre
≥4 µm(c) 22 More than 20,000, up to 40,000
≥6 µm(c) 20 More than 5,000, up to 10,000
≥14 µm(c) 17 More than 640, up to 1,300

Counts are cumulative: particles at ≥14 µm(c) are also counted in the ≥6 and ≥4 µm(c) categories. The oil may look golden and clear, yet contain substantial numbers of microscopic particles.

3. Why contamination matters

Precision-engineered hydraulic components have tight working clearances. Particles can promote abrasive wear, valve sticking, pump damage, reduced efficiency and unplanned downtime. Particle size alone does not determine damage; hardness, shape, quantity and machine duty also matter.

4. Each ISO code step makes a substantial difference

A one-code improvement represents approximately half the particle concentration within that measured size category. A three-code improvement represents about an eightfold reduction. For example, an improvement from 22/20/17 to 18/16/13 indicates approximately sixteenfold lower concentrations at each threshold. Actual results must be measured, not assumed.

5. What cleanliness target should you aim for?

There is no universal ISO cleanliness target for every machine. The correct level depends on equipment type, pressure, component sensitivity and manufacturer requirements. KLEENOIL recommends using the equipment manufacturer's specified target where available.

6. How KLEENOIL cellulose depth filtration works

Instead of relying solely on a thin surface filtration layer, a cellulose depth cartridge captures fine particulate contamination throughout the thickness of its media. In suitable applications, the cellulose can also absorb moisture. KLEENOIL provides permanent bypass units for continuous contamination management and portable mobile rigs for offline oil cleaning.

Cutaway diagram of the KLEENOIL SDFC1888KF85 cellulose depth filter cartridge
SDFC1888KF85 cartridge cross-section showing the wound media, core, outer sleeve and retaining components.

7. Mobile oil filtration in practice

Mobile KLEENOIL filtration systems circulate suitable hydraulic or lubricating oil through a separate cleaning circuit. A filtration plan should take account of reservoir volume, contamination, operating time and oil condition.

KLEENOIL MS2 mobile filtration system photograph 1KLEENOIL MS2 mobile filtration system photograph 2KLEENOIL MS2 mobile filtration system photograph 3

KLEENOIL MS2 mobile filtration system — equipment photographs from different angles.

8. Why before-and-after oil analysis matters

Independent oil sampling and laboratory analysis provide objective evidence of cleanliness and oil condition. Compare particle counts before and after a cleanse, and consider moisture, viscosity, wear metals and chemical condition as appropriate.

Example laboratory oil analysis report with ISO 4406 particle count information
Example laboratory report showing the types of particle-count and oil-condition information available. This is not presented as a before-and-after trial result.

9. Does a better ISO code mean the oil can be reused?

Not automatically. ISO 4406 measures solid particle contamination only. Water content, viscosity, oxidation, additive condition and wear metals may also influence whether the fluid remains suitable. Filtration cannot reverse all chemical degradation or restore depleted additives.

10. Practical ways to maintain cleaner oil

  • Check the cleanliness of new oil before filling sensitive machinery.
  • Keep drums and reservoirs sealed and protect breather and fill points.
  • Maintain filtration elements and investigate recurring particle ingress.
  • Sample regularly and compare trends with the equipment manufacturer's required ISO cleanliness level.
  • Assess water contamination and other fluid properties as well as particle counts.

11. An on-site example

KLEENOIL filtration rig installed beside an IBC during an on-site oil-cleaning trial
KLEENOIL filtration equipment connected to bulk oil storage during a trial application.

12. Ask KLEENOIL for advice

We provide permanent bypass filtration units, mobile filtration systems, replacement cellulose cartridges, laboratory analysis and equipment hire and oil-cleaning services.

KLEENOIL aims to establish whether cleaning is both technically suitable and financially worthwhile before starting a cleanse.

Call the office: 01977 682810
Email: sales@kleenoil.co.uk