Which KLEENOIL MS Filtration System Do I Need? | MS1–MS8 Selection Guide

Not sure whether you need an MS1, MS2, MS4, MS6 or MS8? This practical guide explains the differences between KLEENOIL mobile/offline filtration systems and what to consider before choosing equipment for hydraulic oil, lubricating oil and suitable industrial applications.

Quick selection principle: Choose a system for the volume of oil to be processed, the contamination present, the time available and the oil's viscosity — not flow rate alone. KLEENOIL can help assess the appropriate pump, cartridge arrangement and operating procedure.

MS1 to MS8: flow rate comparison

System Indicative flow Standard Micromag Typical selection consideration
MS1 250 L/hour Configuration-dependent* Smaller systems and controlled lower-volume treatment
MS2 500 L/hour M5 Versatile mobile filtration for small-to-medium reservoirs
MS4 1,000 L/hour M10 Larger oil volumes or shorter processing windows
MS6 1,500 L/hour M10 Higher-volume industrial filtration tasks
MS8 2,000 L/hour M10 Large-volume treatment and demanding turnaround schedules

Indicative nominal flows are not guaranteed site performance. Actual flow depends on oil viscosity and temperature, suction and discharge conditions, cartridge loading and system configuration. *Wall-mounted MS1 systems do not include a Micromag where one cannot be fitted. Confirm the exact configuration before ordering.

How long does a tank take to circulate?

For a simple starting point, divide the tank volume by the system's nominal hourly flow. The figures below indicate one theoretical tank-volume equivalent passing through the system; they are not cleaning-completion times.

Tank volume MS1 MS2 MS4 MS6 MS8
200 L 48 min 24 min 12 min 8 min 6 min
1,000 L 4 h 2 h 1 h 40 min 30 min
4,000 L 16 h 8 h 4 h 2 h 40 min 2 h

Important: In a recirculating tank, processed and unprocessed oil mix. Several effective circulation passes, and sometimes a much longer treatment period, may be necessary. The required duration depends on the contamination type and level, mixing, cartridge condition and the agreed cleanliness and moisture targets. Verify progress with oil sampling rather than relying only on elapsed hours.

Five questions to ask before choosing

  1. How many litres are in the reservoir? A 200-litre tank and a 4,000-litre tank have very different processing demands.
  2. What is the fluid? Identify the oil type, grade, viscosity and operating temperature. Pump suitability and safe operating conditions must be checked.
  3. What is wrong with it? Particle contamination, water ingress, wear debris, oxidation and additive depletion require different assessments. Filtration cannot restore depleted additives or reverse chemical degradation.
  4. How quickly must the work be completed? A higher-capacity system may shorten processing time, but only where the application, fluid and filtration conditions are appropriate.
  5. Is this a one-off clean or an ongoing maintenance requirement? Consider hire or a mobile system for periodic work; a properly specified permanent bypass unit may be better for continuous contamination control.

Why KLEENOIL uses cellulose depth filtration

Cellulose depth filter cartridges provide a substantial filter medium through which suitable oils pass at controlled conditions. The objective is to capture fine particulate matter and help remove water contamination. The most appropriate flow, cartridge arrangement and treatment duration depend on the fluid and the required results. Micromag units, where fitted, provide complementary removal of ferrous wear particles.

When should filtration cartridges be changed?

There is no universal cartridge life. Heavy dirt or water contamination can consume cartridge capacity much faster than routine maintenance. Monitor the system according to its operating instructions and inspect oil condition. Use appropriate oil analysis, including ISO 4406 particle cleanliness and water measurements, to confirm improvement. Do not assume that oil is suitable for reuse solely because it looks clearer.

Buying or hiring a KLEENOIL system

Hire may be suitable for a one-off clean, an initial trial or occasional maintenance. Purchase is generally more useful where multiple machines, repeat servicing or ongoing workshop cleaning justify having equipment available. KLEENOIL can discuss the correct unit, suitable cartridges, hire options, operating arrangements and laboratory sampling.

Ask KLEENOIL to recommend the right MS system

Tell us your reservoir volume, oil type and grade, estimated contamination and the time available. If you have an oil analysis report, please send it too.

Call: 01977 682810
Email: sales@kleenoil.co.uk

Understand ISO 4406 cleanliness codes  |  Water contamination guide  |  Hire and service information